Long distances on the highway can be tedious and being out of touch because of poor cell signal can make things worse. You can be prepared to be in constant contact with family, friends or anyone else with a Mobile Repeater kit from the Repeaterstore.com. With a simple installation, you can have a better signal along your entire route.

Some of the options you’ll want to consider will be:

• Do you want to plug in your phone for best reception
• Do you want to have a wireless situation so you and others in the vehicle can use their phones or data cards
• Are the signal areas you will be passing through exceptionally weak, i.e. mountainous or extremely remote

These varying situations can be dealt with by getting different mobile kits or by building a custom kit. There are a variety of amplifiers and antennas for mobile systems.

Choose one of the complete kits available if you are a traveler with basic needs and requirements, like being on the open road going from town to town or, if you are traveling in a larger vehicle like an RV, you can get one of the larger mobile repeater kits.

Wilson Electronics makes several units to cover your needs:

• 811210  SignalBoost – a unit that attaches to your phone or data card with a Velcro patch
• 801230 Mini-SignalBoost – a low wattage wireless kit
• 801241 SignalBoost Pro – a more powerful wireless kit with multiple power supplies available
• 811201  Direct Connect – kit with a cable connected to your phone antenna port
• 801201 Wireless Vehicle Amplifier -  the most powerful Wilson vehicle amplifier
• 815226  Sleek - Wilson’s newest amplifier kit where you place your phone in a cradle and use an external headset or Bluetooth

For the RV traveler  these Wilson kits work very well:

• 841233  Mini-SignalBoost RV Kit
• 841295  Ambulance and RV Kit for larger vehicles

Take advantage of one of these mobile repeater kits to stay in touch throughout your trip for safety and peace of mind!

Please contact us at 800-761-3041 for help in determining the best solution to your traveling needs.

Be safe and enjoy the sunshine!

Each carrier tries to provide a good usable signal, but unfortunately, many obstacles exist that the carrier cannot overcome: trees, valleys, hills, cement or brick buildings and buildings with metal roofs or metal siding or basements.  These obstacles block or hinder the normally adequate signal which results in broken or dropped voice calls and very slow or non-existent internet service.

Dropped phone calls and slow internet service can be remedied with a cellular booster or repeater kit.  A repeater kit helps this communication by ‘re-transmitting’  the callers signal using:

1. An internal antenna to receive the cell phone signal inside the building, home, car or boat,
2. A cellular amplifier,
3. An external antenna to send a signal to the cell tower. These components are joined together by coaxial cables.

Home or building kits can be customized using different lengths of cable for multiple interior antennas. These antennas can be on a single floor or on multiple floors. The cost of these kits can range from $250 for a small home or RV to $2500 for a large home with multiple floors.  Commercial buildings may require a couple of repeater kits to supply signal to areas from 20,000 to 100,000 square feet.

Whether it’s mobile, home or office that leaves your phone or data card silent, we can tailor a repeater kit for you to bring those essential tools back to life!

The Wi-Ex company has added a new zBoost CI Active Antenna Amplifier for maximum indoor cell signal. The Active Antenna Amplifier greatly improves the performance of an external zBoost CI cell phone signal booster antenna. This coupling optimizes the strong signal reaching the indoor space your trying to cover and maximizes the phone reception, speed of your aircard and Edge and 3g signals including smart phones.

• Your installer can now extend the external cable from the previous 75′ maximum to over 250′ of RG6 cable with the zBoost CI Active Antenna Amplifier
• You can use 4 zBoost base units with 1 zBoost CI external antenna with an Active Antenna Amplifier attached, perfect for multi-unit buildings
• A large home solution at a lower total cost than other manufacturers while offering greater installation flexibility with longer cable runs

Using the zBoost Active Antenna Amplifier with our favorite Wi-Ex zBoost system should greatly enhance the signal strength, offer far better flexibility for the installer and we’ll be able to recommend systems where we couldn’t reach an outside signal before. We look forward to seeing the zBoost Active Antenna Amplifier in the next few months!

Do you have a large, multi story home or a small office, spread out just enough to need more than the basic repeater kits available? You can choose a large building solution and have a  professionally installed system with the CI YX745 Amplifier kit to create a coverage area of up to 12000 square feet. The zboost CI YX745 is available to your professional installer to boost signal on both the 800Mhz and 1900 Mhz bands. The zBoost CI YX745 system includes the amplifier base unit, high gain yagi and panel signal antennas, high gain internal antenna, signal combiner and mounting hardware. Additional professional accessories are available.

• The zBoost  CI YX745 kit works with all US carriers except Nextel and T-Mobile 3G
• Improves cell phone, smart phone and data card communication with your carrier
• Eliminates most dropped or missed calls
• Increases cell phone battery life because of the stronger signal

We don’t have an estimated delivery date from Wi-Ex yet but hope to see this new product in the next few months!

Contact us at 800-761-3041 for updated info on all Wi-Ex equipment.

So what about the 2nd or 3rd floors?
A splitter (859957) is connected right past the two 65dB amplifiers but before the internal Panel antenna. One side of the splitter continues to the Panel mounted on the 1st floor and the other port of the splitter is run up to the 2nd floor for additional coverage needed there.  At this time, however, the signal on the 1st floor is decreased, which means the coverage area on the 1st floor now has gone down.  What a dilemma !

A more efficient way to direct the internal signal is to use a “Tap” which is a type of ‘directional’ splitter. A Tap funnels a certain amount of signal through a specific port.  A common tap we use in multiple-floor installations is a 6dB/1.5dB Tap (#859906) which directs only 25% of the signal to the 6dB port and the remaining 75% signal through the 1.5dB port. This allows 75% of the remaining signal to be sent on to the 2nd & 3rd floors where it is split evenly using the standard 50/50 splitter (#859957).

At some point, after multiple splits/taps, the signal is degraded and will need to be boosted back up so it can continue down the cable. This is when a Pre-amp (811201 or 812201) should be installed to cover more square footage, for instance, on a 4th or 5th floor.  In this example, we would install the pre-amp directly in-line to the cable running up to the 4th & 5th floors. The pre-amp would need AC power, as it is an active amplifier, so plan this installation accordingly. The key to extending the inside coverage to a multi-story building as in this example, is to use Taps (#859906), Splitters (#859957)  and Pre-amps (#811201, 812201) as described

Hopefully this description is helpful;  please give us a call with your custom installation requirement!

RepeaterStore.com

The zBoost YX039 Premium Antenna consists of two directional panel antennas, each with a 18″ jumper cable to connect them to an antenna combiner. The antenna combiner then attaches to a single coaxial cable for connection to the Wi-Ex Base Unit. The new YX039 System is to be used with the zBoost YX510-CEL-PCS dual band repeater kit.

The new and improved accessory antenna system, Wi-Ex zBoost YX039, offers an improved look and better overall signal gain!

Specifications:
This directional antenna system captures signals in both 800 MHz Cellular &1900 MHz PCS bands for the use with zBoost dual-band amplifier systems.
Gain: 8dBi (824-896 MHz) 13dBi (1850-1990 MHz)
Impedance: 75ohms
UPC: 1866390006
Connectors: The two antennas are inputted to the signal combiner, which has an F/Female connector

Kit Contents:
YX021-CEL Cellular Panel Antenna (824-896 MHz)
YX023-PCS Panel Antenna (1850-1990 MHz)
2x 18″ coaxial jumper cablesAntenna combiner
2x U-Bolt and mounting brackets for pole mounting (pole not included)
Instruction manual

Wilson 301201 Dual Band Building Antenna

The Wilson 301201 is a 75 ohm version of the 301202, which we covered in a previous post. The Wilson 301201 is a dual band antenna, suited for outdoor building installation. It’s omni-directional, so receives signal from all directions, and is the perfect exterior antenna option for the Wilson 801262.

Wilson 301155 Dual Band Panel Antenna

The Wilson 301155 is a 75 ohm version of the versatile Wilson 301135. The antenna is a directional panel antenna, which can be used as both the receiving antenna outside or as the broadcast antenna inside. It is directional, and so needs to be pointed towards the nearest cell tower when used outside, or pointed toward the area to provide coverage when used inside.

Wilson 301151 Indoor Ceiling Dome Antenna

The Wilson 301151 is a 75 ohm version of the most popular indoor antenna, the Wilson 301121. This is a broadcast antenna, which is placed after the Wilson 801262 to transmit the boosted signal. It is omni-directional, which means it broadcasts the signal in all directions. It should therefore be placed at the center of the area you wish to cover.

With all these options it can get a little confusing! If you have any questions at all then please give us a call on (800) 761-3041, or send us an email, and we can help design a kit to meet your needs.