RepeaterStore.com has had many successful installations where the building size has exceeded 10,000 sq feet and  up to 40,000 square feet! By starting with the Wilson Dual-Band Ultimate II Repeater kit,  which uses two 65dB amplifiers (Cellular band #801165,  PCS band #801365),  this kit provides an internally amplified signal through one, ceiling mounted Panel antenna (#301135). The coverage given by this Panel antenna is usually limited to the floor it is mounted on because it is a directional antenna that shoots a signal down like a sprinkler.  When mounted on the 1st floor for example, the ceiling- mounted Panel antenna would not push signal back up to the 2nd & 3rd floors.

So what about the 2nd or 3rd floors?
A splitter (859957) is connected right past the two 65dB amplifiers but before the internal Panel antenna. One side of the splitter continues to the Panel mounted on the 1st floor and the other port of the splitter is run up to the 2nd floor for additional coverage needed there.  At this time, however, the signal on the 1st floor is decreased, which means the coverage area on the 1st floor now has gone down.  What a dilemma !

A more efficient way to direct the internal signal is to use a “Tap” which is a type of ‘directional’ splitter. A Tap funnels a certain amount of signal through a specific port.  A common tap we use in multiple-floor installations is a 6dB/1.5dB Tap (#859906) which directs only 25% of the signal to the 6dB port and the remaining 75% signal through the 1.5dB port. This allows 75% of the remaining signal to be sent on to the 2nd & 3rd floors where it is split evenly using the standard 50/50 splitter (#859957).

At some point, after multiple splits/taps, the signal is degraded and will need to be boosted back up so it can continue down the cable. This is when a Pre-amp (811201 or 812201) should be installed to cover more square footage, for instance, on a 4th or 5th floor.  In this example, we would install the pre-amp directly in-line to the cable running up to the 4th & 5th floors. The pre-amp would need AC power, as it is an active amplifier, so plan this installation accordingly. The key to extending the inside coverage to a multi-story building as in this example, is to use Taps (#859906), Splitters (#859957)  and Pre-amps (#811201, 812201) as described

Hopefully this description is helpful;  please give us a call with your custom installation requirement!

RepeaterStore.com

Wi-Ex has upgraded their popular YX029 Premium Antenna, to the dual panel YX039 Premium Antenna System. The gain of the antennas has increased, boosting the signal strength and coverage area of your RepeaterStore cellular amplifier. The updated YX039 uses the YX021 800 MHz panel antenna in place of the 800 MHz yagi antenna that was in the YX029 System. This change gives better performance and is easier to install.

The zBoost YX039 Premium Antenna consists of two directional panel antennas, each with a 18″ jumper cable to connect them to an antenna combiner. The antenna combiner then attaches to a single coaxial cable for connection to the Wi-Ex Base Unit. The new YX039 System is to be used with the zBoost YX510-CEL-PCS dual band repeater kit.

The new and improved accessory antenna system, Wi-Ex zBoost YX039, offers an improved look and better overall signal gain!

Specifications:
This directional antenna system captures signals in both 800 MHz Cellular &1900 MHz PCS bands for the use with zBoost dual-band amplifier systems.
Gain: 8dBi (824-896 MHz) 13dBi (1850-1990 MHz)
Impedance: 75ohms
UPC: 1866390006
Connectors: The two antennas are inputted to the signal combiner, which has an F/Female connector

Kit Contents:
YX021-CEL Cellular Panel Antenna (824-896 MHz)
YX023-PCS Panel Antenna (1850-1990 MHz)
2x 18″ coaxial jumper cablesAntenna combiner
2x U-Bolt and mounting brackets for pole mounting (pole not included)
Instruction manual

Don’t miss this opportunity to save $50.00, we’re offering a mail-in rebate on the CelLynx 5BARz Road Warrior repeater kit!

The 5BARz Road Warrior, now even more affordable, is a simple plug-in cell signal booster for your car, home, office or hotel room! To use, just plug in the cigarette adapter into your vehicle or the ac adapter in your home, office, or hotel room, place your phone in the dock provided and you’re all set to go!

Raise your signal with the 5BARz Road Warrior:

• No installation – just plug in when you need a boost!
• Faster internet – including 3G
• Stronger signals and better reception
• Works with your cell phone and data cards
• Good for all US carriers except Iden and T-Mobile 3G

Take advantage of this $50.00 mail-in rebate until June 30, 2010 and say goodbye to weak signals and dropped calls!

A Recreational Vehicle on the move can have significant cell reception problems depending on the location its traveling in. A good way to minimize dropped calls & increase reception to cellular phones / broadband data cards is to install a Cellular Repeater Kit in the coach.

A Cellular Repeater Kit will allow you to make calls when very little cell phone signal exists. This booster will also reduce dropped calls and increase internet speeds. We have had good success with Wilson Electronics Repeater kits customized for use in Motorhomes & RVs.

Wilson Electronics is well regarded in the industry because of their high quality.

Cell Phone Boosters or Repeaters are very simple to setup and they do not require expert installation. A Repeater kit consists of 3 major components; an external antenna, an amplifier or booster and an internal antenna that gives cellular coverage inside the RV.

Kits can range from $300 for a single-phone style amp to $600 for a more powerful amp that can support multiple cell phones and/or broadband data cards. A few of these kits are listed below.

Single Cell phone use:

http://www.repeaterstore.com/products/Wilson-841233-Wilson-841233-Mini-SignalBoost-RV-Kit

Multiple Cell  Phones or Data Cards:

http://www.repeaterstore.com/products/Wilson-841295-Wilson-841295-Ambulance-and-RV-Repeater-Kit

Apple has introduced the long awaited tablet, calling it the  iPad!  The iPad has Wi-Fi and Bluetooth connectivity built-in, comes with 16, 32 or 64 gigabytes of memory, has a 9.7 inch multi-touch screen yet only weighs in at 1.5 pounds. The company claims the device has a battery that can last 10 hours and can sit for a month on standby before needing a charge.

Some of the features include:

• Surfing the web with Apples Safari browser                                                            
• Sending and receiving e-mails
• Saving and sharing photos
• an electronic book store and book reading interface
• a video player
• iPod software for playing music
• a newspaper reader program

Apple will sell a version with 3G data plans and without a long term contract. For those who experience a weak signal on the AT&T service we have a range of repeaters that will greatly improve your 3G data service. We recommend a dual band repeater so you can also have improved reception on your cell phone including the iPhone.

You can find a list of dual band repeaters on the following Repeaterstore page:

http://www.repeaterstore.com/support/buyer%20guide/dual-band-repeaters.html

Which one you need depends on the area you need to cover. Here is a list of the most popular kits we have, broken down by coverage area:

Mid-Range (up to 2,500 sq ft.)
zBoost YX510: http://www.repeaterstore.com/products/repeaterkits/wi-ex/zboost-dual-band.html
Wilson SOHO 801245: http://www.repeaterstore.com/products/repeaterkits/wilson/soho.html

Large Range (5,000 to 10,000 sq ft.):
Wilson SOHO “Premium” and “Ultimate” configurations. This is the same amplifier as before, but in more powerful kit combinations. Scroll down the Wilson SOHO page: http://www.repeaterstore.com/products/repeaterkits/wilson/soho.html

Very Large Range (greater than 10,000 sq ft.):
Wilson Ultimate Repeater Kit: http://www.repeaterstore.com/products/repeaterkits/wilson/wilson-dual-band-ultimate.html